|
FORCED AIR
FORCED
AIR
|
|
|
Goodman Manufacturing Company, L.P. ("Goodman")
produces a complete line of
residential and commercial air conditioning and heating equipment at
its
three modern, high technology factories, totaling over 1,200,000
square feet
in Houston, Texas, Dayton and Fayetteville, Tennessee. Goodman's
equipment
is sold through a worldwide network of independent distributors and
installers who are dedicated to uphold the company's high standards of
quality.
The Goodman philosophy: Be the highest quality,
lowest cost producer of heating and air conditioning equipment in
the world.
Is it successful? Goodman's share of the market
has grown faster than any other major manufacturer. Our Quality and
Value speak for themselves.
Goodman has been very successful at increasing its presence in the
mature HVAC industry, due primarily to the following philosophies:
- High quality at a low cost equals value
- Maintain low overhead
- Invest money normally spent on advertising and promotions in
research and development, which translates to high quality at a low
cost for the consumer
- Create products that are engineered for reliable long life,
utilizing the best components with some of the lowest failure rates
in the industry
- Offer one of the best warranties in the industry
|
| |
|
|
GMS8/GDS8 Series
80% AFUE Single-Stage, Multi-Speed |
|
The
Goodman® GMS8/GDS8 Single-Stage, Multi-Speed
Gas Furnaces feature a patented aluminized steel tubular
heat exchanger and energy-efficient Hot Surface Ignition
system. These furnaces are run-tested for heating or
combination heating/cooling applications. With a
heavy-gauge, reinforced, wrap-around insulated steel
cabinet and durable baked enamel finish, these units can
be installed in a variety of locations.
-
Corrosion-resistant, aluminized-steel tubular heat
exchanger
- Designed for
multi-position installation—GMS8: upflow, horizontal
right or left; GDS8: dedicated downflow
- Energy-saving,
reliable Hot Surface Ignition system, featuring a
Norton® Mini-Igniter with patented
adaptive learning algorithm to maximize igniter life
- Aluminized-steel
inshot burners
- Energy-saving PSC,
multi-speed, direct-drive blower motor
- Quiet,
corrosion-resistant, induced-draft blower assembly
- Integrated furnace
control with diagnostics
- Low-voltage terminal
blocks
- Multiple flame
roll-out switches, blower door safety switch, outlet
air-limit switch and pressure switch for proof of
combustion air
- 40VA transformer for
heating and air conditioning control service
- Combination
redundant gas valve and regulator
- A rotating
combustion air blower (GMS8) that provides the
option of venting the furnace through the top,
right-hand side or left-hand side
- Specific models
comply with California NOx Standards
- Foil-face insulation
lines the heat exchanger compartment
- Coil and furnace fit
flush for easy installation
- Convenient left or
right connection for gas and electric service
- Bottom or side air
inlet (GMS8)
- Removable, solid
bottom (GMS8)
- Heavy-gauge,
reinforced, fully insulated steel cabinet with
durable, baked-enamel, Architectural Gray paint
finish
|
|
GMS80453ANA*
|
45,000
|
36,000
|
3.0
|
14" x 28" x 39"
|
120
|
|
GMS80703ANA*
|
70,000
|
56,000
|
3.0
|
14" x 28" x 39"
|
130
|
|
GMS80704BNA*
|
70,000
|
56,000
|
4.0
|
17-1/2" x 28" x
39"
|
143
|
|
GMS80903BNA
|
90,000
|
72,000
|
3.0
|
17-1/2" x 28" x
39"
|
153
|
|
GMS80904BNA*
|
90,000
|
72,000
|
4.0
|
17-1/2" x 28" x
39"
|
153
|
|
GMS80905CNA*
|
90,000
|
72,000
|
5.0
|
21" x 28" x 39"
|
163
|
|
GMS81155CNA*
|
115,000
|
92,000
|
5.0
|
21" x 28" x 39"
|
163
|
|
GMS81405DNA*
|
140,000
|
112,000
|
5.0
|
24-1/2" x 28" x
39"
|
183
|
|
GDS80453ANA*
|
45,000
|
36,000
|
3.0
|
14" x 28" x 39"
|
120
|
|
GDS80703ANA*
|
70,000
|
56,000
|
3.0
|
14" x 28" x 39"
|
130
|
|
GDS80904BNA*
|
90,000
|
72,000
|
4.0
|
17-1/2" x 28" x
39"
|
153
|
|
GDS81155CNA
|
115,000
|
92,000
|
5.0
|
21" x 28" x 39"
|
175
|
|
|
|
GMV8
Series 80%
AFUE Two-Stage, Variable-Speed |
|
|
The
Goodman® GMV8 Two-Stage, Variable-Speed Gas
Furnace features a patented aluminized-steel tubular
heat exchanger and energy-efficient Hot Surface Ignition
system. This furnace is run-tested for heating or
combination heating/cooling applications. With a
heavy-gauge, reinforced, wrap-around insulated steel
cabinet and durable baked enamel finish, these units can
be installed in a variety of locations.
-
Corrosion-resistant, aluminized-steel tubular heat
exchanger
- Designed for
multi-position installation—upflow, horizontal right
or left
- Energy-saving,
reliable Hot Surface Ignition system, featuring a
Norton® Mini-Igniter with patented
adaptive learning algorithm to maximize igniter life
- Auto-Comfort mode
helps to efficiently create and maintain a
comfortable climate by intuitively adjusting to the
room’s environment
- Aluminized-steel
inshot burners
- 2-stage gas valve
and super-efficient, quiet variable-speed blower
motor
- Quiet, 2-speed,
induced-draft blower assembly
- Integrated furnace
control with diagnostics
- Low-voltage terminal
blocks
- Multiple flame
roll-out switches, blower door safety switch, outlet
air-limit switch and pressure switch for proof of
combustion air
- 40VA transformer for
heating and air conditioning control service
- A rotating
combustion air blower that provides the option of
venting the furnace through the top, right-hand side
or left-hand side
- All models comply
with California NOx Standards
- Foil-face insulation
lines the heat exchanger compartment
- Coil and furnace fit
flush for easy installation
- Convenient left or
right connection for gas and electric service
- Bottom or side air
inlet
- Removable, solid
bottom
- Heavy-gauge,
reinforced, fully insulated steel cabinet with
durable, baked-enamel, Architectural Gray paint
finish
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GMV80703BXA
|
|
57,400
|
|
|
1.5-3.0 |
17" x 28" x 39"
|
|
|
GMV80905CXA
|
|
|
|
54,000 |
2.0-5.0 |
21" x 28" x 39"
|
178 |
|
GMV81155CXA
|
|
|
|
|
2.0-5.0 |
21" x 28" x 39"
|
194 |
|
|
|
GMS9/GCS9 Series
93% AFUE Single-Stage, Multi-Speed |
|
The
Goodman® GMS9/GCS9 Single-Stage, Multi-Speed
Gas Furnaces feature a patented aluminized-steel tubular
heat exchanger and energy-efficient Hot Surface Ignition
system. These furnaces are run-tested for heating or
combination heating/cooling applications. With a
corrosion-resistant, painted steel cabinet, these units
can be installed in a variety of locations.
-
Corrosion-resistant, aluminized-steel tubular heat
exchanger and stainless-steel recuperative coil for
maximum efficiency
- Designed for
multi-position installation—GMS9: upflow, horizontal
right or left; GCS9: downflow, horizontal right or
left
- Energy-saving,
reliable Hot Surface Ignition system, featuring a
Norton® Mini-Igniter with patented
adaptive learning algorithm to maximize igniter life
- Aluminized-steel
inshot burners
- Energy-saving PSC,
multi-speed, direct-drive blower motor
- Quiet,
corrosion-resistant, induced-draft blower assembly
- Integrated furnace
control with diagnostics
- Low-voltage terminal
blocks
- Multiple flame
roll-out switches, blower door safety switch, outlet
air-limit switch and pressure switch for proof of
combustion air
- 40VA transformer for
heating and air conditioning control service
- Combination
redundant gas valve and regulator
- Top venting is
standard; alternate flue/vent located on right side
(GMS9)
- All models comply
with California NOx Standards
- Suitable for direct
vent (2-pipe) or non-direct vent (1-pipe)
applications
- Foil-face insulation
lines the heat exchanger compartment
- Coil and furnace fit
flush for easy installation
- Convenient left or
right connection for gas and electric service
- Bottom or side air
inlet (GMS9)
- Removable, solid
bottom (GMS9)
- Heavy-gauge,
reinforced, fully insulated steel cabinet with
durable, baked-enamel, Architectural Gray paint
finish
|
|
GMS90453BXA
|
46,000
|
42,800
|
3.0
|
17-1/2" x 28" x
40"
|
132
|
|
GMS90703BXA
|
69,000
|
64,400
|
3.0
|
17-1/2" x 28" x
40"
|
135
|
|
GMS90904CXA
|
92,000
|
86,000
|
4.0
|
21" x 28" x 40"
|
158
|
|
GMS91155DXA
|
115,000
|
106,500
|
5.0
|
24-1/2" x 28" x
40"
|
175
|
|
GCS90453BXA
|
46,000
|
42,800
|
3.0
|
17-1/2" x 28" x
40"
|
132
|
|
GCS90703BXA
|
69,000
|
64,400
|
3.0
|
17-1/2" x 28" x
40"
|
135
|
|
GCS90904CXA
|
92,000
|
86,000
|
4.0
|
21" x 28" x 40"
|
156
|
|
GCS91155DXA
|
115,000
|
106,500
|
5.0
|
24-1/2" x 28" x
40"
|
175
|
|
|
|
GMV9/GCV9 Series
93% AFUE Two-Stage, Variable-Speed |
|
The
Goodman® GMV9/GCV9 Two-Stage, Variable-Speed
Gas Furnace features a patented aluminized-steel tubular
heat exchanger and energy-efficient Hot Surface Ignition
system. These furnaces are run-tested for heating or
combination heating/cooling applications. With a
corrosion-resistant, painted steel cabinet, these units
can be installed in a variety of locations.
-
Corrosion-resistant, aluminized-steel tubular heat
exchanger and stainless-steel recuperative coil for
maximum efficiency
- Designed for
multi-position installation—GMV9: upflow, horizontal
right or left; GCV9: downflow, horizontal right or
left
- Energy-saving,
reliable Hot Surface Ignition system, featuring a
Norton® Mini-Igniter with patented
adaptive learning algorithm to maximize igniter life
- Auto-Comfort mode
helps to efficiently create and maintain a
comfortable climate by intuitively adjusting to the
room’s environment
- Aluminized-steel
inshot burners
- 2-stage gas valve
and super-efficient, quiet variable-speed blower
motor
- Quiet, 2-speed,
induced-draft blower assembly
- Integrated furnace
control with diagnostics
- Low-voltage terminal
blocks
- Multiple flame
roll-out switches, blower door safety switch, outlet
air-limit switch and pressure switch for proof of
combustion air
- 40VA transformer for
heating and air conditioning control service
- Top venting is
standard; alternate flue/vent located on the right
side (GMV9)
- All models comply
with California NOx Standards
- Suitable for direct
vent (2-pipe) or non-direct vent (1-pipe)
applications
- Foil-face insulation
lines the heat exchanger compartment
- Coil and furnace fit
flush for easy installation
- Convenient left or
right connection for gas and electric service
- Bottom or side air
inlet (GMV9)
- Removable, solid
bottom (GMV9)
- Heavy-gauge,
reinforced, fully insulated steel cabinet with
durable, baked-enamel, Architectural Gray paint
finish
|
|
GMV90704CXA
|
|
64,200
|
|
|
1.5-4.0 |
21" x 28" x 40"
|
135 |
|
GMV90905DXA
|
|
|
|
59,500 |
2.0-5.0 |
24-1/2" x 28" x 40"
|
172 |
|
GMV91155DXA
|
|
|
|
|
2.0-5.0 |
24-1/2" x 28" x 40"
|
175 |
|
GCV90704CXA
|
|
64,200
|
|
|
1.5-4.0 |
21" x 28" x 40"
|
135 |
|
GCV90905DXA
|
|
|
|
60,100 |
2.0-5.0 |
24-1/2" x 28" x 40"
|
172 |
|
|
|
GMV95 Series 95%
AFUE
Two-Stage, Variable-Speed |
|
The
Goodman® GMV95 Two-Stage, Variable-Speed Gas Furnace
features a patented aluminized-steel tubular heat
exchanger and energy-efficient Hot Surface Ignition
system. This furnace is run-tested for heating or
combination heating/cooling applications. The 95% AFUE
GMV95 qualifies for the new 2006 $200 energy tax
credit. Standard
Features
- Corrosion-resistant, aluminized-steel tubular
heat exchanger and stainless-steel recuperative coil
- Lifetime Limited Warranty on Heat Exchanger plus
10-year Furnace Replacement Limited Warranty
- Designed for multi-position installation (upflow,
horizontal right or left)
- Energy-saving Hot Surface Ignition system with
Norton® Mini-Igniter and patented adaptive learning
algorithm
- Auto-Comfort mode to maintain a comfortable
climate
- 2-stage gas valve
- Super-efficient, quiet variable-speed blower
motor
- Quiet, 2-speed, induced-draft blower assembly
- Integrated furnace control with diagnostics
- Low-voltage terminal blocks
- Suitable for direct vent (2-pipe) or non-direct
vent (1-pipe) applications
- Convenient left or right connection for
gas/electric service
- All models comply with California NOx Standards
Cabinet Features
- Heavy-gauge, reinforced, fully insulated steel
cabinet with durable, Architectural Gray
baked-enamel finish
- Foil-faced insulation lines the heat exchanger
compartment
- Top venting standard; alternate flue/vent
located on right
- Bottom or side air inlet; removable, solid
bottom
|
|
Model |
Rated Heating
High Fire |
Rated Heating
Low Fire |
Available Cooling |
Dimensions
W" x D" x H" |
Ship Weight (lbs) |
| | | |